Sparks behind the waveguide cover, a hum with no heat, or a unit that keeps running after you open the door: one call to Acdc Appliance Repair connects you with a licensed, insured independent microwave pro near Paris who works on over-the-range, built-in and drawer models.
The cabinet hides a high-voltage capacitor that can store a deadly charge even when the unit is unplugged. That single part is the reason microwave repair should go to a trained pro, not to a weekend project.
We run a free referral line for homeowners. A dispatcher hears what the microwave is doing and connects you with an independent local technician who knows both the high-voltage side and the installation side of these units.
Each pro we connect you with runs an independent shop with the license and insurance local rules call for. Asking for proof on arrival is perfectly normal.
Some microwave parts cost more than people expect. You get a written, upfront quote from the technician before work begins, which lets you weigh it against buying new.
We look for a pro already working near Paris. A same-day slot opens up regularly when local pros have breathing room, and the arrival window gets set while you are on the line.
The right pro arrives with an insulated capacitor discharge tool, a meter for testing the diode and transformer windings, the tech sheet for your model, and a survey meter to confirm no leakage once the repair is done.
These cover the over-the-range, built-in wall, drawer and convection combo models that are worth repairing. Each starts with a safe capacitor discharge before any testing.
The fan spins, the light glows, the plate turns, and the coffee comes out cold. The usual suspects are the magnetron, the high-voltage diode, the capacitor, or the transformer. The technician tests each one with the power off and the capacitor discharged.
Blue flashes along the side wall usually come from a greasy or burnt waveguide cover, chipped cavity paint, or a damaged rack support on a convection model. Left alone, arcing can pit the cavity and ruin the magnetron.
Microwaves use a chain of door interlock switches plus a monitor switch. When a switch sticks, the monitor switch shorts the line on purpose and blows the line fuse, so the whole unit goes dark. A unit that runs with the door open needs to be unplugged right away.
Dead buttons, phantom beeps, or a unit that keeps running after the timer ends point to the membrane touchpad or a stuck relay on the control board. The technician reads the keypad circuit with a meter and checks the relays before ordering parts.
An over-the-range microwave also works as the range hood. Grinding fans, a lamp that never turns on, greasy metal filters, and a spent charcoal filter on recirculating installs all get handled here.
A plate that will not spin usually needs a turntable motor or a new coupler. OTR units that sag or rattle may have a loose wall bracket or top bolts pulled through the cabinet, which is a safety issue with a hot stove below.
Use this as a quick read before you call. Share what you see with the dispatcher, and the technician can bring the most likely parts.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Runs, light on, no heat | Magnetron, diode, capacitor or transformer failure | Each high-voltage part with the capacitor discharged |
| Completely dead, no display | Blown line fuse from a failed door switch | Fuse, interlock switches, monitor switch |
| Sparks or smoke inside | Burnt waveguide cover, chipped cavity paint | Cover, cavity surface, stirrer, rack supports |
| Keeps running at zero or with door open | Welded relay or failed interlock | Control board relays and door switch chain |
| Plate will not turn | Turntable motor or coupler | Motor continuity, coupler, roller ring |
| Vent fan loud or dead | Fan motor bearings, greasy filters | Fan motor, damper, grease and charcoal filters |
A basic countertop microwave usually is not worth a service call, and most technicians will tell you so on the phone. Over-the-range units, built-in wall models, drawer microwaves and convection combos are a different story. They cost more, they fit a cutout or bracket, and swapping one means trim kits, cabinet work and a vent connection.
Unplug it, leave the cover on, and call. A dispatcher answers day and night.
Tell the dispatcher what type of microwave you have, whether it sits over the range, in a wall, or in a drawer, and what it is doing. If you can, read off the model number from the tag inside the door frame.
We route the job to an independent pro near Paris and give you the arrival window on the call. When the schedule cooperates, a technician often arrives the day you call.
First comes a safe discharge of the capacitor, then meter tests on the magnetron, diode, transformer, door switches and board. An OTR unit sometimes has to be lifted off its mounting plate. The written, upfront quote comes before any work begins, and you decide.
After the repair, the pro heats a cup of water to confirm output and, after any high-voltage work, sweeps the door seal with a microwave survey meter to check for leakage. Written coverage for parts and labor is the norm among the pros we connect; ask for it.
Our over-the-range microwave went completely dark mid-popcorn. The technician found a blown line fuse, then traced it to a cracked door switch. He replaced both and showed me why the fuse would have blown again if he had only swapped the fuse.
The built-in in our wall oven stack hummed but did not heat. A new one would have meant a new trim kit too. The tech tested the diode and magnetron, replaced the magnetron, and checked for leakage with a meter before he left.
Sparks were jumping off the side wall every time I warmed soup. It was a burnt waveguide cover soaked with grease. Quick fix, and he showed me how to keep that cover clean.
The drawer microwave kept running even at zero, which scared us. The technician diagnosed a stuck relay on the control board, ordered the exact board, and installed it on a return visit.
A microwave that runs without heating has a fault in its high-voltage section: magnetron, diode, capacitor or transformer. Because that circuit can hold a deadly charge, the testing belongs with a pro who knows how to discharge it safely.
No. Stop using it until it is checked. Sparks usually come from a dirty or burnt waveguide cover or chipped cavity paint, and continued arcing can damage the magnetron. If there is smoke, keep the door closed and unplug it if you can reach the cord safely.
Most of the time a dead microwave has blown its line fuse, and the fuse blew because a door switch failed and the monitor switch tripped it. A good pro replaces the failed switch along with the fuse, not just the fuse.
Frequently. Over-the-range and built-in units are expensive and fitted to the opening, so a new one brings its own installation costs. Small countertop models are usually better replaced. With a written quote from the pro in hand, you can make the call.
We strongly advise against it. That capacitor stores enough energy to kill, even with the plug pulled. Keep the outer case on and leave the discharge to a technician with proper insulated tools.
Ask for it, especially after high-voltage or door work. Many pros sweep the door seal and vents with a microwave survey meter before they leave, to confirm the unit is sealed properly.
Our line connects homeowners and renters across Paris and the surrounding area with independent microwave technicians. Calls go to whoever has a route nearby, and that matters when an over-the-range unit has to be taken down for service.
The dispatch line is open 24 hours a day. A late-night call is usually booked for the next morning, and daytime calls often turn into same-day visits when a local pro has an opening.
